板壳塑性屈曲中的佯谬及其研究进展

本文详细论述了板壳塑性屈曲中的佯谬及其研究进展。并对现有的各种观点作了分析讨论。     

PLASTIC BUCKLING OF STIFFENED TORISPHERICAL SHELL

ＰＬＡＳＴＩＣＢＵＣＫＬＩＮＧＯＦＳＴＩＦＦＥＮＥＤＴＯＲＩＳＰＨＥＲＩＣＡＬＳＨＥＬＬＨａｏＧａｎｇ（郝刚）ＺｅｎｇＧｕａｎｇｗｕ（曾广武）ＨａｏＱｉａｎｇ（郝强）（ＲｅｃｅｉｖｅｄＤｅｃ．３０，１９９４．ＣｏｍｍｕｎｉｃａｔｅｄｂｙＰａｎＬｉｚｈ...     

Generalized Method of Separation of Variables on the Nonlinear Elastic-Plastic Wave Motion

The method of separation of variables is developed in addition to the Karman method and the method of characteristics for the wave motion of uniaxial stress in rods. Rate-independent theory is considered and it is shown that the plastic wave speed is independent of the constant n in the stress-strain law. Stresses are determined in explicit forms for two cases.     

添加聚合物对混合层流场特性影响的实验研究

叙述了适用于粘弹性流体混合层流场的实验装置的设计和研制．采用二维激光多普勒系统对混合层流场进行了测量，得到了平均速度剖面、动量厚度、湍流脉动强度、雷诺应力等一些流场的基本特征量．结果表明，混合层中加入聚合物后流场将有较大的变化，同时也说明本文所研制的实验装置满足实验的要求．     

Lee极值原理与结构的大挠度塑性动力响应

本文介绍了利用Lee 极值原理确定结构的大挠度塑性动力响应的数值方法,给出了在均布冲击载荷作用下的理想刚塑性门形框架的大挠度进化模态解,指出如果模态形式取得合适,可使进化模态解接近于真实解.这样得到的门形框架的大挠度模态解与文献[8]中的实验结果和文献[9]中的大挠度完全解都符合得很好.     

加筋板结构的大变形

本文对受均布载荷，具有一根纵向加筋多根横向加筋的加筋板结构的残余变形导出了近似理论分析方法。从假设变形模态出发，依据极限分析原理获得可能变形模态和模态判别条件。在变形分析中，计及膜力（轴力）影响，但忽略弹性影响，得到了各变形模态下的残余变形估算公式。最后根据本文的理论分析方法和ＡＤＩＮＡ程序作了实例计算，两者的变形模态和最大残余变形均十分一致     

A theory of large-strain isotropic thermoplasticity based on metric transformation tensors

Summary A formulation of isotropic thermoplasticity for arbitrary large elastic and plastic strains is presented. The underlying concept is the introduction of a metric transformation tensor which maps a locally defined six-dimensional plastic metric onto the metric of the current configuration. This mixed-variant tensor field provides a basis for the definition of a local isotropic hyperelastic stress response in the thermoplastic solid. Following this fundamental assumption, we derive a consistent internal variable formulation of thermoplasticity in a Lagrangian as well as a Eulerian geometric setting. On the numerical side, we discuss in detail an objective integration algorithm for the mixed-variant plastic flow rule. The special feature here is a new representation of the stress return and the algorithmic elastoplastic moduli in the eigenvalue space of the Eulerian plastic metric for plane problems. Furthermore, an algorithm for the solution of the coupled problem is formulated based on an operator split of the global field equations of thermoplasticity. The paper concludes with two representative numerical simulations of thermoplastic deformation processes.     

铸铁材料在边界润滑条件下形成薄片状磨屑的塑性流动机制

本文在铸铁材料油润滑线接触滑动磨损状态研究的基础上,对边界润滑区典型的薄片状磨屑之形成过程进行了考察。通过对磨损表面的几何形貌、磨屑的形态和内部显微组织变化的分析,提出了薄片状磨屑的塑性流动形成机制。作者认为,薄片状磨屑的形成是磨损表面材料在局部应力和摩擦热的作用下以3种方式发生塑性流动的结果:当摩擦方向垂直于磨削加工条纹时为单侧塑性流动;当摩擦方向平行于磨削加工条纹时为双侧塑性流动;而在峰顶平台(磨削加工粗糙条纹磨合后形成的微平台)较大且载荷较高时,则为平台上的材料沿着摩擦方向向前挤压流动。     

分析薄壳塑性动力响应问题的一种数值方法

探索薄壳塑性动力响应问题的分析与数值方法,是当今力学中的重要课题之一。笔者曾给出联合应用拉普拉斯变换和最小二乘法分析梁、板、壳塑性动力响应的方法。本文分别针对承受中载的短壳和长壳问题,给出只用最小二乘法分析其塑性动力响应的方法。     

POST-BUCKLING AND IMPERFECTION SENSITIVITY OF A COLUMN WITH AN EQUILATERAL TRIANGULAR CROSS-SECTION IN THE PLASTIC RANGE

The asymmetric initial post-buckling corresponding to the lowest bifurcation load andthe imperfection sensitivity are analysed in detail for a compressed simply supported column with anequilateral triangular cross-section in the plastic range.The effect of elastic unloading is taken into ac-count in the analysis.The asymptotic relations,including high order terms,among the load,the am-plitude of imperfection and the amplitude of the bifurcation mode are realized.The results show thatthe maximum supported load is very sensitive to imperfection.